Bantam BC8HP Operations Instructions download pdf (Page 11)

STATION

- Chg. mode (Charge mode) : You can select a method of charging,

they are Normal, Balance, FAST.

Balance mode; This is for equalizing the individual voltages of

battery pack. The battery pack should have the individual cell

connector. Connect it to the individual port at the charger with a

suitable connection cable or adaptor that fits with the type of

connector of your battery pack. And also, you should to connect the

battery output plug to the output of charger. The internal processor of

the charger will monitor the voltages of each cell and controls the

charging current to equalize the voltage.

FAST mode; To charge the battery earlier, this program eliminates

certain term of CV range. Actually, the charging current will go to 1/5

of initial value gradually at the end of process, while the normal

charging goes to 1/10 at the end of CV term. The charging capacity

may be bit smaller than normal charging but the charging time can be

reduced.

- End curr. (End current) : Set the final charging current at

termination. The end current should be less than the initial

charge current.

Auto; The process will be terminated when the charging current go

to 1/10 of its initial value. Otherwise, the charge current will be

decreased until the designated value has been reached. (Auto,

60~500mA)

- Chk. time (Check time) : BC8DX recognizes the cell-count of

Lithium battery automatically and shows the counts at the beginning

of charge or discharge process to avoid from erroneous input by

user. But the battery which has been discharged deeply can be

perceived the cell-count incorrectly. The charger will work on the

cell-count anyway during the check time. But if the charger finds the

wrong cell-count at the end of check time, the process will be

terminated with an error message. To prevent the error, you can set

the time term to verify the cell-count by the charger. Normally, 10

minutes are enough to perceive the cell-count correctly. For the

battery of larger capacity, you may extend the time term. (5 ~ 250

min.)

Chg curr : 5.0A

Chg mode : Normal

End curr : Auto

Chk time : 10min

Max capa : 100%

LiPo[ 1 ] 6S(22.2V)

3000mAh CHARGE

Chg curr : 5.0A

Chg mode : Normal

End curr : Auto

Chk time : 10min

Max capa : 100%

LiPo[ 1 ] 6S(22.2V)

3000mAh CHARGE

▶

Chg curr : 5.0A

Chg mode : Normal

End curr : Auto

Chk time : 10min

Max capa : 100%

LiPo[ 1 ] 6S(22.2V)

3000mAh CHARGE

▶

- 11 -

It is very important to know the exact type of battery to be charged, nominal voltage and

capacity. Not to know these facts is the reason why batteries are damaged and improperly

cared for. Read the battery’s label and instruction sheet carefully, or consult the battery

supplier to get those facts.

▶

For balance mode charge, BANTAM supplies some balance adaptors for various brands of

Lixx batteries in the market. The balance adaptor should be acceptable at this charger.

The suitable adaptors for single battery pack are;

Part no. EAC133: PolyQuest type, EAC134: Align type, EAC138: Kokam/Graupner type and

EAC139: FlightPower/ThunderPower type.

The suitable adaptors for balancing multiple battery packs are;

Part no. EAC153: PolyQuest type, EAC154: Align type, EAC158: Kokam/Graupner type and

EAC159: FlightPower/ThunderPower type.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 23 24

Comments to this Manuals

No comments

Bantam BC8HP Operations Instructions Page 11

Comments to this Manuals